If your 2008 Honda Pilot key fob battery has died, you need to change it as soon as possible. There are several ways to do this. Read on to learn how to replace a dead key fob battery and how to repair a damaged fob. You may also need to replace the ignition cylinder if the battery is dead.
How to Replace a Dead 2008 Honda Pilot Key Fob Battery
If you’re wondering how to replace a dead battery in a 2008 Honda pilot key fob, you’ve come to the right place. To fix your key fob’s dead battery, start by removing the cover. The back cover is usually held on with a plastic hook, so remove it carefully. Then, unscrew the battery, and carefully pull out the key fob.
Most Honda key fobs have a flat round three-volt battery, but they may vary slightly by model and year. Check your manual to find out the exact battery you need. In most cases, the battery is not difficult to replace. However, if you’re not sure how to remove the old battery, you can take it to a retail store and purchase a replacement battery.
Repair a damaged key fob
If your key fob battery goes dead, it is easy to repair. A small screwdriver with a flathead tip will remove the dead battery from the fob. Be sure to gently pull the battery out, and avoid stripping the metal electrical contacts. Now, replace the dead battery with a new CR-2032 3volt coin cell battery. Insert the new battery in the appropriate position, with the negative side facing up and the positive side facing down. Then, snap the back cover onto the front part of the fob. To tighten the screw, tamperproof tape, or Loctite Blue will help prevent the screw from becoming loose or stripped.
If you do not have a multimeter or other multitool, you can simply insert a flathead screwdriver into the slot in the top of the key fob. Using your other hand, insert the key fob, lining it up with the front. Snap it back into place.
Replace a dead ignition cylinder
If you’re having trouble getting the car key to start your car, it may be time to replace the ignition cylinder. The key might have fallen out of the ignition cylinder or it may be rusted. The key may also be worn or have teeth that are bent and may need to be straightened. For more complicated problems, you can ask an expert to check the ignition cylinder. In the meantime, you can use an inflatable wedge or a straightened wire hanger as an alternative to a key.
First, remove the dead battery. To do this, you’ll need a flathead screwdriver. Make sure not to damage the metal electrical contacts when removing the battery. Next, insert a new CR2032 3-volt coin cell battery. Make sure the positive side of the battery is facing up and the negative side is facing down. You can now attach the back cover of the key fob by snapping it over the front part. Once the cover is securely attached, you can screw the key fob back onto the front part.
Change the ignition cylinder on a dead key fob
If you’ve lost your Pilot remote key, you might need to change the ignition cylinder and start over. Normally, these remote controls and key fobs last for two to three years, so changing them is not a major problem. You can reprogramme your key fob by using a scan tool or an OBDII scanner. However, if you’re unable to successfully program the key, you might have to take the vehicle to an authorized dealer.
Before you take your Pilot to a locksmith, be sure to check the battery. The battery may have been sitting on the shelf for a while, which means it might not be functioning at all. When you replace the battery, make sure to get a new one from a reputable store with quick stock movement. Otherwise, you might not get the replacement you need for your car.
Get a new key fob
Your Honda key fob is powered by a flat, three-volt battery. If yours is not working, you may need to get a new battery. If you want to replace your key fob yourself, you can do so with a jeweler’s screwdriver or by following the instructions on the owner’s manual.
It should be easy to replace, but if you want to make sure that your key fob functions correctly, you need to program it inside your Honda. To do this, turn your key to the “On” position and hold it there for about one second. Then, turn your key off and repeat the process two more times.
You can get a new battery for your Honda Pilot by removing the old battery from the key fob. You can use a key or a small flathead screwdriver to pry open the fob. Then, you can take the old battery to a store to replace it with a new one. If you liked our How to Replace a Dead 2008 Honda Pilot Key Fob Battery article and if you have further questions, contact us.
